Skip to content
CLChloe.

About

Who We Are

One plant behind every insulator: shell, insert and the item number

Zhejiang Chloe Electric makes insulators and insulation support for low- and medium-voltage equipment. The insulating body and the metal insert are made in the same plant, so an insulator is not assembled out of two suppliers' tolerances.

Moulding and porcelain runs on one line — epoxy, porcelain and composite silicone-rubber bodies in red, grey, yellow and white — and metal work on the other: inserts, thread forms, flanges and the fixings that go with the insulator. The two meet at the assembly bench, where height, thread and unit are made up to the ordered specification.

The product pages follow the same item list the shop builds from, so the heights, specifications and units match what leaves the bench.

  • Body line: epoxy, porcelain and composite shells in the phase colours
  • Metal line: inserts, thread forms, flanges and fixing hardware
  • Insulators checked dielectrically and dimensionally, then packed to the ordered specification
  • Selection support from the people who read the specifications
2015Trading from Yueqing
Works building and yard in Yueqing
Company Journey

The range widened with the enquiries that came in

Bodies first, then the insert and thread combinations, then the range moved online. Export orders and non-standard heights followed because those enquiries needed all of it.

Stage 01

Epoxy and porcelain bodies, with the colour named in the order

The first lines were the stand-off bodies the market already used, moulded in epoxy and fired in porcelain. The shell colour became an ordering decision rather than an accessory: red, grey, yellow or white for the phase marking.

  1. 01Epoxy stand-off bodies added to the range.
  2. 02Porcelain and composite bodies listed as separate families.
  3. 03Shell colour made part of the order line.
Moulded insulator bodies staged on a bench
The People

Moulding, metal work and inspection — three sign-offs, one plant

The people who own the body line, the insert line and the outgoing bench answer selection questions directly, so a specification does not travel through a call centre to reach them.

  • Chen Wei

    Plant Manager

    Owns the insulator lines end to end — bodies, inserts, make-up and export packing — for the KLY / MNS / EL / SM and ZJ ranges.

    Open full profile
  • Lin Xiaoyun

    Body Moulding Lead

    Holds the body side of the range: the epoxy, porcelain and composite shells, and colour matching across a batch.

    Open full profile
  • Zhao Gang

    Inserts and Threading Supervisor

    Runs the metal inserts, thread forms and flanges — top and bottom thread combinations and the heights written into the specification.

    Open full profile
Company Achievement

What the range covers

Series, item numbers, voltage classes and packing — the same figures shown on the product pages.

  • 28Insulator series families
  • 2,651Item numbers in the range
  • 210Product lines
  • 1,257Item numbers with a photograph
Inside The Works

From a moulded body to a packed insulator

Bodies, inserts, sorted colours and the bench where an insulator is checked before it is boxed. Tell us the equipment and the panel, and we come back with item numbers.

Start An Enquiry
What Clients Say

Judged on the answer that names an item number

Feedback from the duties that reach the insulator desk.

They read our SM insulator configuration back to us before quoting and confirmed the thread at each end against our panel drawing.
Purchasing Engineer, switchgear builder
The busbar spacing on our cabinet was not a standard one. A drawing went over, a variant came back, and it dropped onto the existing frame.
Electrical Designer, distribution cabinet builder
Three families and two colours on one order, and the packing list matched the item numbers exactly.
Warehouse Lead, panel builder
A height we could not find in the range was quoted from a drawing. They said so in the first reply.
Project Buyer, substation programme
Clients & Partners

Who the insulators are built for

Switchgear, busbar systems, transformers and the overhead and substation equipment they sit in.

Switchgear & Controlgear
Busbar Systems
Distribution Cabinets
Transformers
Motor & Generator Terminals
Overhead Lines
Substation Equipment
Custom Panel Builders
News & Insights

Selection notes from the desk

Insulators checked against a mounting panel

Height, Thread and the Panel in Between

The failures that turn an insulator order into a site problem are almost never electrical. They are an insulator that is too short for the spacing it stands in, or a thread that will not start on the fixing already drilled.

  • Jun 11, 2026
  • Zhao Gang
  • Selection
  • 6 min read
Continue Reading